Solar Hot Water Tank

1. Tank in tank new design 2, CE/PED approved, high quality 3, OEM/ODM 4, Food material SUS304/316L 5, Multi-function

Pressurized Water Tank Features:1. It adopts the Automatic argon welding solitary, and the lifespan is especially long. 2. For the all closed separated tank, the rated pressure is 0.6Mpa. 3. It adopts the super thick insulation layer, because it can keep warm and save electric energy. 4. It adopts the one-way anti-over pressure device, if the pressure is more than 0.6Mpa, the relief valve can reduce pressure and overflow automatically, so that the dirt in the tank can be drained easily. 5. Temperature pressure relief valve can protect overpressure. When the leakage of the electric current is more than 10mA, it could cut off the electrical source automatically in order to keep safe. 6. There is the anode magnesium bar inside the tank to extend the lifespan. 7. The separated tank is especially suitable for water use of houses, hospitals, and the hotels.

-----------------------------------------------------------------------------------------------------------

Description

(1)The place of installing the water heater must be closed to the place of using, the temperature / pressure relief valve, temperature controller and electric heat pipe must be faced the direction where is easy to maintain. The data plate should be easy to read, and the space above the tank should be over the height of the tank so as to check and change the positive pole protection device.

(2)The space around the tank should be convenient when pulling down the whole tank to maintain or change the parts in case of necessity.

(3)The tank is with vertical type; it must be installed in the level that can bear the weight of the product.

(4)Power socket must be installed in the position that the water can’t spray, so as not to produce vapor when taking a shower, then induce the socket leak electricity.

A. The connection of cold water pipe:The cold-water outlet is closed to the bottom of the power covering, and the interface is G1/2”. First connect the one-way safe drainage valve with the water heater, then join the close valve and connect with tap water pipe.Note: When the pressure in the tank reaches some value, the one-way safe drainage valve can unload the pressure to tap water pipe automatically. So when you electrify to the tank, please keep the cold close valve open.

B. The joining of hot water pipe:The hot water outlet is on the top of the tank, and the interface is G1/2”. After connecting the close valve in the outlet pipe of the hot water, then use the tube in order to lead hot water to the place of the hot water requirement.

C. The installation of temperature / pressure relief valve:Twine the whorl well with the crude airproof strap, but it can’t over the whorl terminal surface, then fasten temperature / pressure relief valve in the installation place. Note that the overflow should face underside so the water comes out conveniently.

--------------------------------------------------------------------------------------------------------

Usage

(1). Water supply:First, open the close valve of the outlet of the tank and one hot faucet, and keep the water pipeline open. When the hot faucet works normally, which means water is full and then you could close the faucet.

(2). Settlement of hot water temperature:The temperature regulation range of the temperature controller of the tank is 30~75°C, and the set temperature at 65°C before dispatched from the factory.Warning: please pay attention to the scalding dangerous of the hot water, especially for the children and elders.

(3). Inserting the plug:There must be good earth and three feet when you use the plug, and make the socket and power dry. The electric current that the outlet and wire allow passing is more than the one of the nominal current of the water heater.

(4). Using of hot water:After heating to the established temperature, the power showing light will be put out, and then the water heater will be the state of keeping warm automatically. At this time, you can use the hot water, and obtain the suitable temperature by mixed regulating with the cold faucet. The cold water in the water heater will supplement automatically while using the hot water, at the same time the temperature controller will set up an electric circuit to heat automatically. If you don’t use the water in the short time, please don’t close the power of the tank because its good performance of keeping warm doesn’t waste too much electricity.

(5). Close the water heater:Close the power first, and then close the hot water globe valve of the water heater.

Specifications

Place of Origin	China	Model Number	JX
Price Terms	FOB, CIF	Brand Name	JX& OEM
Payment Terms	T/T, L/C	Minimum Order	1 sets
Supply Ability	3,000 sets/month	Delivery Time	7 days

 

Model	100L	150L	200L	250	300L
Rated pressure	0.6 MPa	0.6 MPa	0.6 MPa	0.6 MPa	0.6 MPa
Working pressure	0.55 MPa	0.55 MPa	0.55 MPa	0.55 MPa	0.55 MPa
Rated power	1.5KW	1.5KW	1.5KW	1.5KW	1.5KW
Temp. Control	30-75°C	30-75°C	30-75°C	30-75°C	30-75°C
Qty per 20’/40’ container	90/194	63/134	53/114	44/94	38/81

Solar Hot Water Tank